ZoneMapper draws the courses you enter. It does not decide where a boundary is. It is not a survey, and it is not legal advice. When the line matters — a sale, a dispute, a permit that has to match a recorded survey — compare the drawing with the deed and with a survey.
Who this is for
Surveyors checking a description, title searchers reading a chain of deeds, real estate attorneys looking at a legal description, and landowners who want to see the lot their deed describes. Homeowners preparing a site plan can use the same outline for setbacks and lot area, or they can keep tracing the lot by clicking corners. Both ways create the lot boundary.
What to have in front of you
- The deed’s courses, starting at the point of beginning. A course is a bearing and a distance. A curve also names a radius, an arc length or a delta (the central angle), and whether the path bends left or right.
- A map open in ZoneMapper: a survey image, an aerial photo from an address, or any other base you want the line drawn on.
- The map scale. Set the scale before you plot. Until you do, a distance in the deed is only a number. It is not a length in feet on the drawing. Starting from an address sets the scale for you. On an uploaded survey, use Set scale and a labeled line whose length you know.
How to read a call
A quadrant bearing is the form most older deeds use. N 45°30'15" E, 100.00 feet means: stand at the current point, face north, turn 45 degrees, 30 minutes, and 15 seconds toward the east, and go 100 feet. The angle in a quadrant bearing is from 0 to 90 degrees. N 90° E is due east. S 0° E is due south.
An azimuth is measured clockwise from north, all the way around. Azimuth 90° is due east. Azimuth 270° is due west. You can write degrees only, or degrees, minutes, and seconds.
Due North, 100 feet is a full course: direction north, distance 100 feet. If a call gives no unit, ZoneMapper treats the number as feet. Chains (66 feet), rods or poles (16.5 feet), and links (0.66 feet) are converted when the call names that unit.
The first course starts at the point of beginning. You can name it in the panel (“iron pin at the northwest corner”) so the closure readout shows that name. The name is a label for you. It does not place the pin on a monument in the ground.
Bearings are drawn with north toward the top of the page. If your survey sheet is rotated, set the scale on a line you trust and turn the north arrow to match the sheet. The deed itself is still plotted with north up.
Curves
When a call gives a radius, an arc length or a delta, and left or right, ZoneMapper draws a curve rather than a straight chord. “Curve to the right” means the path turns right as you walk the line.
If the curve follows a straight course, that course is the direction of the curve as it starts. You can also type a chord bearing or a tangent bearing. A chord bearing by itself, with no radius, is not enough to reconstruct the arc, so that call is drawn as the straight chord and the panel says so.
One curve you can paste after a straight course:
N 90°00'00" E, 100 feet curve to the right, radius 50 feet, delta 90°00'00" S 00°00'00" E, 50 feet N 90°00'00" W, 150 feet N 00°00'00" E, 100 feet
Plot it
1. Open the app and a map
Use Open map for a survey or plat, or Start from address for an aerial photo. Lot boundary tracing is still there if you would rather click the corners.
2. Set the scale
The Plot a deed panel says whether the scale is set. If it is not, distances will not mean feet on the drawing. Calibrate, then come back to the calls.
3. Paste or enter the courses
In the side panel, open Plot a deed. Paste the description, or use Add a course for one bearing and distance at a time. A short closing example:
N 00°00'00" E, 80.00 feet N 90°00'00" E, 60.00 feet S 00°00'00" E, 80.00 feet N 90°00'00" W, 60.00 feet
That rectangle is 80 feet by 60 feet, 4,800 square feet, and it closes.
4. Read the closure before you trust the shape
After the last call, the panel shows two numbers:
- Linear misclosure — how far the end of the last course sits from the point of beginning, in feet, and in which direction (east or west, north or south).
- Precision — the length of the calls divided by that gap, written as 1:N. A bigger N means a smaller gap for the length of the description. If the end lands on the start, the panel says the traverse closes.
ZoneMapper does not “fix” a deed that misses. The corners stay where the calls put them, and the line from the last point back to the start is the gap. A small gap can be rounding in an old description. A large gap is often a course that was mistyped — check the deed again. Deciding what a gap means for a boundary is work for a surveyor, not for this drawing.
5. Plot the lot
Choose Plot deed. The traverse becomes the lot boundary and is centered on the sheet. Lot area, including the gap when there is one, shows on the map and in the compliance figures. From there you can add setbacks, structures, and a PDF the same way as a lot you traced by hand.
A note on area
The lot area is the area of the shape that was plotted, curves included. It is the area of those courses on this drawing, at the scale you set. It is not a certified acreage.
More guides
- Shed site plan — once the lot is drawn, a permit plan uses the same boundary
- Fence site plan
- All guides
ZoneMapper is a drawing tool. It plots the calls you enter and shows the arithmetic of the closure. It does not establish a boundary, interpret a deed, or give legal advice. Verify the drawing against the recorded description and a survey when the line matters.